SSDs do not require defragmentation. Since they do not contain a physical disk, there is no need to organise the data in order to reduce seek time. Therefore defragmenting an SSD is not effective. Also, defragmenting an SSD can put undue wear on specific areas of the drive. SSDs are designed to write data as evenly as possible over the entire drive to reduce undue wear to any one location. Defragmenting your SSD drive a couple of times will not harm it. However, if it is done continuously over a long period, it may reduce the life of the drive.
Over time, most of the storage locations on an SSD are written to. When they get written to again, they need to be conditioned in order to accept new data. This can cause a delay and is seen as a reduction in drive performance. Garbage Collection is a function built into a SSD that reconditions empty storage locations so when new data is written to the drive, there are locations on the SSD ready to accept data.
Although the Garbage Collection function is built into most SSD drives, some drives perform this more efficiently than others. TRIM resolves this issue by letting the operating system tell the drive when to perform this function. At this time, only Windows 7, Server 2008, MacOS 10.7 and newer versions of Linux use TRIM. Also, there are no RAID configurations that support TRIM no matter what operating system is used. All of Kingston's MLC based SSDNow drives are TRIM compatible. Some of our first generation SSDNow drives are not TRIM compatible.
First, open an Elevated Command Prompt window.
To open an Elevated Command Prompt window: Click on Start Orb > Type "CMD.exe" in Search box > Right click on "CMD" and select "Run as Administrator" (If you receive a prompt confirmation, click YES)
To verify that the TRIM command is enabled, type the following and press enter in the Elevated command:
fsutil behavior query disabledeletenotify
The results will be as follows: DisableDeleteNotify = 1 (Windows TRIM commands are disabled) DisableDeleteNotify = 0 (Windows TRIM commands are enabled)
To enable the TRIM command,type the following and press enter in the Elevated command:
fsutil behavior set disabledeletenotify 0
To disable the TRIM command,type the following and press enter in the Elevated command:
fsutil behavior set disabledeletenotify 1
Open the Control Panel, open Administrative Tools and then open Computer Management. Click on Disk Management and see if the SSD drive is shown in the right window pane. If it is, right-click on where it is labelled as disk 1, disk 2, etc. and select "Initialize disk" (this may come up automatically when you go into Disk Management).
In XP, right click on the area to the right of that and choose "New Partition". Then choose "Primary Partition" in the partition wizard. Continue with the wizard by choosing the size, drive letter and formatting of the partition.
In Windows Vista and 7, right click on the area to the right of the disk label and choose "New Simple Volume". Continue with the wizard by choosing the size, drive letter and formatting of the partition.
In MacOS, a "disk insertion" window will appear. Click on the "Initialize" button. This will take you to the disk utility. Select the Kingston drive from the list of drives on the left side of the window. From the actions available, choose Partition. For the "Volume Scheme", choose "1 partition". For the format, choose MacOS extended for a permanent drive. Choose ExFAT for an external drive (available on MacOS 10.6.6 and above). Click Apply. A warning window will appear stating that you will erase all data from the drive. Click on the partition button at the bottom.
Our SATA III (6Gbit/s) SSDs are tested to be backwards compatible to SATA II (3Gbit/s). They are not designed or tested to be backwards compatible with SATA I ports (1.5Gbit/s). Most systems made before 2008 used SATA I ports. Our SSDs will likely not work in these systems.
When the SSD is recognised in the BIOS, but the Windows 7 installation does not detect the drive:
Follow these steps:
Disconnect any other hard drives or SSDs. Boot the Windows 7 installation disk. Choose repair, then advanced, then command prompt. Type: "diskpart" without quotes and press Enter. You will see a prompt labeled "diskpart". Type the following commands and press Enter after each one.
Diskpart > Select Disk 0
Diskpart > Clean
Diskpart > Create Partition Primary Align=1024
Diskpart > Format Quick FS=NTFS
Diskpart > List Partition
Diskpart > Active
Diskpart > Exit
Then, reboot the computer to the Windows 7 installation disk.
Performance decreases have been reported on some SSDNow drives. If you have an older SSD drive that does not have effective Garbage Collection, SSD drive performance will decrease over time. This is due to the way the system overwrites data that has been flagged for deletion.
Try using the Secure Erasetool like HDDErase to wipe the drive and restore it to its original condition.
Any of our SSDs can be used in RAID. However, due to endurance specifications, only certain part numbers should be used in RAID. For servers, please contact Kingston to determine the best Kingston SSD to use for your workload.
Self-Monitoring Analysis and Reporting Technology (SMART) is a built-in monitoring capability in hard drives and SSDs. It can allow users to monitor the health of a device. It does this through monitoring software designed specifically for the SMART feature. All of our SSDNow drives support SMART.
The Windows Experience Index (WEI) merely measures the relative capability of components. The WEI only runs for a short time and does not measure the interactions of components under a software load, but rather characteristics or your hardware.
The WEI does not thereforemeasure the performance of a system, but merely the relative hardwarecapabilities when running Windows 7. An article about the WEI can be foundhere: http://blogs.msdn.com/b/e7/archive/2009/01/19/engineering-the-windows-7-windows-experience-index.aspx
In Vista, the WEI scores ranged from 1.0 to 5.9. In Windows 7, the range has been extended upward to 7.9.
Kingston realises the importance of keeping our customers' personal data and information confidential and secure. Kingston takes measures to ensure the security of all of our customers' personal information when a Solid State Drive (SSD) is returned to our RMA facility for warranty replacement or repair. When an SSD reaches our repair centre, it will undergo a thorough testing process. During the first phase of testing, an ATA Secure Erase is performed on the SSD, which erases all data and information. ATA Secure Erase is federally approved by the National Institute of Standards and Technology (NIST 800-88) for legal sanitisation of confidential user data. If the SSD is not in a functional state and not capable of undergoing an ATA Secure Erase, the SSD is dismantled and the NAND Flash Memory is destroyed.
ElectroStatic Discharge, ESD is simply the discharge of built-up static electricity. ESD should not be taken lightly as this is one of the few things that an individual can do to damage or destroy their computer or hardware components. It is like when you rub your feet on the carpet and you touch something metal. ESD can occur without the user feeling a shock and will occur when only working on the inside of the computer or handling hardware.
How to help prevent ESD
The best method of preventing ESD is to use an ESD wrist strap or an earthing mat or table. However, because most users do not have access to these items, we have included the below steps to help reduce the chance of ESD as much as possible.
To learn more about ESD and how to protect your electronics, please refer to the below site.
Monday-Friday 6 a.m.-6 p.m. PST
Complete a short form for prompt resolution
Monday-Friday 6 a.m.-6 p.m. PST