Yes. When the device is plugged into a USB port on a computer, it will become a USB card reader and USB hub. If the wireless connection is on when you plug it into the USB port, you will need to turn it off before the the computer will detect it.
FAQ: KFR-042313-MLW-02
FAQ: KFR-042313-MLW-03
The MobileLite Wireless supports FAT, FAT32, NTFS, and exFAT file systems.
FAQ: KFR-042313-MLW-04
The MobileLite Wireless reader will support up to 2TB storage devices.
FAQ: KFR-082913-MLW-14
하드 드라이브가 인식되지 않는 데는 몇 가지 이유가 있을 수 있습니다. 지원되지 않는 형식을 드라이브가 사용했을 수 있습니다. 하드 드라이브는 FAT32, exFAT 또는 NTFS 중 하나로 포맷되어야 합니다. Mobilelite Wireless는 MacOS 또는 Linux 형식을 지원하지 않습니다. 파티션 유형은 GPT일 수 있습니다. 이 파티션 유형은 주로 드라이브를 부팅하고 Mobilelite Wireless로 읽히는 연결을 위해서만 사용됩니다. 파티션 유형을 MBR로 변경해야 합니다. 드라이브에 몇가지 유형의 보안 기능을 실행해야 할 것입니다. 암호화 또는 드라이브와 함께 제공된 암호 보호 소프트웨어를 실행할 수 있었습니다. 이는 반드시 비활성화되어야 합니다.
FAQ: KFR-090916-MLW-18
No. The default static IP address (192.168.200.254) is non-configurable.
KFR-042313-MLW-05
FAQ: KFR-042313-MLW-05
There is a reset button next to the power button on the MobileLite Wireless. It can only be accessed by using a paper clip. With the MobileLite Wireless on, press and hold this button for about 15 seconds or until the bridged LED lights up blue.The MobileLite Wireless will reinitiate and be ready for use once the WiFi LED lights up again.Note:This will not delete any data stored on USB/SD/SDC but it will remove any changes to the network I.D., password, etc.
KFR-042313-MLW-08
FAQ: KFR-042313-MLW-08
The MobileLite Wireless reader has two Mac addresses: One for LAN and one for WAN for bridging. The MAC address listed on the back of the device is the LAN MAC address and will not be the same as the WAN MAC address.The WAN MAC address is HEX digit (0-9 and A-F) higher than what is on the back of the device.
FAQ: KFR-070513-MLW-12
Yes. Have both devices plugged into the MLW and open the app.
FAQ: KFR-082913-MLW-13
MobileLite Wireless is its own wireless network. Joining this network will automatically replace your existing Internet connection, be it your iPad, iPhone, or home/office Wi-Fi network.MobileLite Wireless does offer a bridged network connection which allows you to access the Internet while continuing to stream MobileLite content. This feature basically allows you to “bridge” together two networks.
To do this, connect to MobileLite Wireless network and follow these steps:
KFR-051614-MLW-06
FAQ: KFR-051614-MLW-06
This may need to change the default Wi-Fi channel. The MobileLite Wireless defaults to channel 11.If there are already too many connections near you using this channel, it could cause the MobileLite Wireless not to connect.
To resolve this:
FAQ: KFR-050614-MLW-07
First make sure there is another WiFi connection available besides the MobileLite Wireless and you are connected to it. Then try the following:
If you are still having problems, please contact our technical support.
FAQ: KFR-042313-MLW-09
The MobileLite Wireless device has two configurations when it comes to security.The ‘Off’ state indicates that the device will not be password protected with WPA2 security, which will virtually allow anyone to connect to the device.
The ‘On’ state indicates that the device will be password protected with WPA2 security and only those supplied with the password will be able to connect to the MobileLite Wireless device.
The on/off state will only come into play when trying to access the contents that are available by the MobileLite Wireless device.
The MobileLite Wireless device supports both WEP and WPA2 bridged connections.
FAQ: KFR-042313-MLW-11
In some cases, external USB drives will need to be connected to the MLW before it is powered on in order for the app to see the drive. Also verify the drive is formatted in one of the following file systems: FAT, FAT32, NTFS, or exFAT. Also, you will need to disable any security enabled on the USB hard drive such as BitLocker or security software that came with the drive.
FAQ: KFR-033015-MLW-16