Gigabyte - MW53-HP0 Motherboard
-
Bus Architecture
USB 2.0/3.x Type-A
SSD - SATA 2.5-inch 9.5mm
USB 2.0/3.x Type-C
SSD M.2 NVME 2280 (Heat Sink)
-
8 Socket(s)
-
Intel Xeon W-3500/3400 Series Intel W790
Intel Xeon W-2500/2400 Series Intel W790
-
Configurations up to 512GB can be reached using Kingston's 16, 32, and 64GB modules IN IDENTICAL GROUPS OF FOUR.
Important Configuration Notes
- MODULES MUST BE ORDERED AND INSTALLED IN IDENTICAL GROUPS OF FOUR for Quad Channel mode.
- Mixing x4 and x8 modules is allowed, however not within the same Quad Channel bank group.
- JEDEC spec "KSM" Server Premier Registered DIMMs will operate at 4800MT/s installed in 1DPC (1 DIMM per Channel) in Quad Channel configuration using Intel Xeon W9, W7 and W5 series processors. Due to processor/chipset limitations, 4800MT/s DDR5 RDIMMs installed in 2DPC (2 DIMMs per Channel) in Quad Channel configuration are limited to operate at and will safely clock down to 4400MT/s. Xeon W3 series and W5-3423 / W5-3433 models limit memory speed to 4400MT/s, regardless of DIMM configuration.
- Refer to motherboard manual and QVL for supported memory configurations and speeds.
Kingston FURY Configuration Notes
- Per Gigabyte, this motherboard does not support XMP-based memory overclocking.
- Kingston FURY Plug N Play (automatic overclock) featured memory will run up to the speed allowed by the manufacturer's system BIOS. PnP cannot increase the system memory speed faster than is allowed by the manufacturer's BIOS.
- Mixing modules or kits of different speeds/timings/voltages is not recommended and may cause instability.
- If a K8 "Kit of 8" part is not listed for a particular speed/capacity, it is not recommended to install two K4 "Kit of 4" together. K8 kits are only listed if the configuration has been tested as stable.
Compatible Upgrades For Your System
- Server Premier
- Solid-State Drives
-
Part Number: KSM56R46BD8-32MH
- Part Number: KSM56R46BD8-32MH
- DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX8 1.1V 288-pin 16Gbit Micron H
- Spec Sheet PDF
- PCN
DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX8 1.1V 288-pin 16Gbit Micron H
-
Part Number: KSM56R46BD8-32HA
- Part Number: KSM56R46BD8-32HA
- DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX8 1.1V 288-pin 16Gbit Hynix A
- Spec Sheet PDF
- PCN
DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX8 1.1V 288-pin 16Gbit Hynix A
-
Part Number: KSM56R46BS8PMI-16HAI
- Part Number: KSM56R46BS8PMI-16HAI
- DDR5 5600MT/s ECC Registered DIMM CL46 x80 1RX8 1.1V 288-pin 16Gbit Hynix A IDT/Renesas
- Spec Sheet PDF
- PCN
DDR5 5600MT/s ECC Registered DIMM CL46 x80 1RX8 1.1V 288-pin 16Gbit Hynix A IDT/Renesas
-
Part Number: KSM56R46BD8PMI-32HAI
- Part Number: KSM56R46BD8PMI-32HAI
- DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX8 1.1V 288-pin 16Gbit Hynix A IDT/Renesas
- Spec Sheet PDF
- PCN
DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX8 1.1V 288-pin 16Gbit Hynix A IDT/Renesas
-
Part Number: KSM56R46BD4PMI-64HAI
- Part Number: KSM56R46BD4PMI-64HAI
- DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX4 1.1V 288-pin 16Gbit Hynix A IDT/Renesas
- Spec Sheet PDF
- PCN
DDR5 5600MT/s ECC Registered DIMM CL46 x80 2RX4 1.1V 288-pin 16Gbit Hynix A IDT/Renesas
Kingston FURY Renegade with Heatsink (SFYRSK/xxxG, SFYRDK/xxxG) will fit in most systems that can accommodate its size (~80mm x 23.67mm x 10.5mm). This includes a variety of motherboards, desktops, gaming PCs and the PlayStation 5. If you are uncertain whether it will fit, please review your system manufacturer’s support manual, or contact Kingston Technical Support. Note: Some small-form-factor systems like Intel® NUC cannot physically accommodate the height of the heatsink. In these circumstances, we suggest FURY Renegade without heatsink (SFYRS/xxxG, SFYRD/xxxG).
-
Part Number: SEDC600ME/1920G
- Part Number: SEDC600ME/1920G
- Designed for Data Center Environments
- On-board Power Loss Protection (PLP)
- Low latency and predictable IO
- Includes Acronis cloning software
- TCG Opal 2.0, AES 256-bit encryption
- 560MB/s Read, 530MB/s Write
- Learn more
-
Part Number: SEDC600M/1920G
- Part Number: SEDC600M/1920G
- Designed for Data Center Environments
- On-board Power Loss Protection (PLP)
- Consistent latency and IOPS, reliable QoS
- Includes Acronis cloning software
- 560MB/s Read, 530MB/s Write
- Learn more
-
Part Number: SEDC2000BYM8/240G
- Part Number: SEDC2000BYM8/240G
- Data Center Class SSD for Enterprise applications
- PCIe 4.0 NVMe M.2 SSD
- Includes Acronis cloning software
- 4500 MB/s Read, 400 MB/s Write
- Learn more
-
Part Number: SEDC2000BM8/480G
- Part Number: SEDC2000BM8/480G
- Data Center Class SSD for Enterprise applications
- PCIe 4.0 NVMe M.2 SSD
- Includes Acronis cloning software
- 7000 MB/s Read, 800 MB/s Write
- PCN
- Learn more